Speed monitor

Function and appearance

The sensor has an integrated integrated speed monitoring function: there are pulse recognition, detection, and processor in the same shell, and the ability to output, convert, drive and amplify the pulse signal at the same time; the shape can be seen in the following figure: its shell is mainly It is composed of a copper shell with a diameter of 30mm and a length of 72mm (thread part 65mm, 7mm at the label) and a plastic head of 1mm thickness and a plastic tail of 6mm thickness (with an action indicator and a potentiometer to adjust the speed); with speed monitoring sensitivity High, 

easy to use, waterproof, anti-fouling and other effects.

Working principle

The sensor uses the tail speed adjustment potentiometer to preset the frequency ft (speed). When the moving parts (mainly iron, copper, etc.) to be monitored rotate at a certain frequency fc (speed) 

within 10 mm from the sensor head, the sensor Corresponding pulse signals are generated internally through magnetic induction and input into the control circuit. After the circuit is amplified 

and shaped, the count is performed; then the count value obtained is the rotation frequency fc (speed) of the moving part to be monitored and the preset frequency ft (speed )Compare. If fc> ft, 

then the sensor generates a signal to cause the switch or relay to close; if fc

Instructions for use

The sensor is activated for 9 seconds (switch or relay closed state) immediately after poweron to allow the monitored object to have a starting process. After the delay start, if the action 

indicator at the end of the sensor does not light, it means that the rotation frequency (speed) of the 

monitored object is lower than the preset frequency (speed) of the sensor, then the sensor or relay is in the disconnected state. The potentiometer that adjusts the speed of the tail slowly rotates the 

adjustment screw counterclockwise to make the action indicator light, and the sensor or relay is closed; on the contrary, after the delay start, the action indicator light at the end of the sensor is 

always on, indicating that the monitored object rotates If the frequency (rotation speed) is higher than the preset frequency (rotation speed) of the sensor, then the sensor or relay is in the closed state. At this time, the potentiometer at the rear of the sensor that adjusts the rotation speed can be slowly rotated clockwise to make the action indicator light off. , The sensor or relay is off again.

Usually in actual use, if the sensor or relay is in the off state, the preset frequency (speed) of the sensor is set to 80% of the rotation frequency (speed) of the monitored object during normal operation.

Types/ characteristic			IM30-D1P/                     XSA-V10801		IM30-D1N/                               XSA-V10801		IM30-D1L/                        XSA-V10801		IM30-A2/                             XSA-V11801		IM30-u/                                            XSA-12081
			PNP DC PNP		NPN DC NPN		DC two wires		AC two lines		AC and DC two-wire universal
(sn)Rated sensing distance (sn)			10mm		10mm		10mm		10mm		10mm
Adjustable frequency range			6-150 pulses / min, 20-999 pulses / min, 120-3000 pulses / min, 480-12000 pulses / min
Weight (kg)			0.300		0.300		0.300		0.300		0.300
Connection method			Molded cable, 3 × 0.34mm2, 2m long				Molded cable, 2 × 0.5mm2, 2m long
Degree of protection according to IEC 60529 IP67			IP67
Range of motion			0...8mm
Repeat accuracy			3% of the actual detection distance Sr
Detection accuracy			3 ... 15% of the set frequency Fr
Operating temperature			－ 25... ＋ 70℃
Output status indication			LED
Rated voltage			12...48V  DC 12 ... 48V with reverse polarity protection						～ 24...240V		AC / DC 24 ... 240V
Voltage range (including pulsation)			直流 10...58V						～ 20...264V		AC / DC 20 ... 264V
Switching capacity			≤ 200mA，带过载和短路保护 With overload and short circuit protection						～ 5...350mA		DC 5 ... 200mA
On-state voltage drop			≤ 1.8V				≤ 5.7V
Leakage current							≤ 1.5mA
No-load current consumption			≤ 15mA
Switching frequency			48,000 pulses / min
Power-on delay			9±s20%+1/Fr

Potentiometer adjustment curve and installation

Installation method

Wiring diagram

Range of use

This series of sensors provides an economical solution for issues such as slip detection, conveyor belt damage, transmission shaft shear and overload, and motor protection. It can be applied to the following machines: conveyor belts, chain bucket elevators, Archimedes screws, grinders, crushers, water pumps, centrifugal dryers, mixers, motors, etc.